Home > Perle > Perle Media Converters > Perle Stand-Alone Media Converters > Perle Unmanaged Media Converters > Perle Unmanaged Fiber to Fiber > Perle Unmanaged 1000SX Fiber to Fiber >

05060484

05060484
See any errors on this page?
Please let us know.
  
Perle S-1000MM-M2LC2 - Gigabit Ethernet Fiber to Fiber Media Converter. 1000BASESX  multimode (LC) to 1000BASELX 1310nm Extended multimode (LC) [2km /6562 ft.]
MSRP: $1,147.00
ESP Price: $894.66
Contact us for Partner Pricing. (more info)


Free Shipping
Availability: Usually Ships in 24 Hours; However, Due To Shortages Contact Sales to Verify
Product Code: 05060484

Description Technical Specs Drivers & Downloads
 

Perle's feature rich S-1000MM Gigabit Fiber to Fiber Media Converters enable transparent fiber extension of 1000Base-SX multimode fiber to 1000Base-SX multimode or 1000Base-LX/EX/ZX/BX single mode fiber.

Perle's advanced features make the end to end fiber link completely transparent. This allows for more efficient troubleshooting and less on-site maintenance. In addition, a lifetime warranty and free worldwide technical support make Perle's S-1000MM Gigabit Fiber to Fiber Media Converters the smart choice for IT professionals.

Whether you need to extend multimode to multimode or multimode to single mode, Perle has an extensive range of S-1000MM Gigabit Fiber to Fiber Media Converters to meet your fiber conversion requirement.
Features
  • 1000Base-SX to 1000Base-X Fiber to Fiber Media Converters
  • Multimode to multimode or multimode to single mode
  • Extend multimode fiber to 160km and beyond ( through cascading )
  • Choice in SC, LC and ST fiber connector models
  • Signal regeneration prevents signal degradation
  • Advanced Features: Smart Link Pass-Through, Fiber Fault Alert, loopback for each fiber connection

S-1000MM Fiber to Fiber Features: 1000Base-SX to 1000Base-X

Auto-Negotiation (802.3ab) The 1000Base-X fiber interfaces negotiate according to 802.3 clause 37.
Smart Link Pass-Through When the Link Mode switch is placed into Smart Link Pass-Through mode, the 1000BASE-X link on one port will reflect the state of the other 1000Base-X media converter port. This feature can be used whether fiber auto-negotiation is enabled or disabled.
Fiber Fault Alert With Fiber Fault Alert the state of the 1000Base-X receiver is passed to the 1000Base-X transmitter. This provides fault notification to the partner device attached to the 1000Base-X interface of the media converter. If the 1000Base-X transmitter is off as a result of this fault it will be turned on periodically to allow the condition to clear should the partner device on the 1000Base-X be using a similar technique. This eliminates the possibility of lockouts that occur with some media converters. Applies only when fiber auto-negotiation is disabled.
Signal Regeneration Signal regeneration maintains signal integrity and allows for maximum fiber to fiber connections without degradation.
Cascading Media converters can be cascaded. Two or more media converters can be chained in a link to achieve even greater distances.
Pause (IEEE 802.3x) Pause signaling is an IEEE feature that temporarily suspends data transmission between two devices in the event that one of the devices becomes overwhelmed. The media converter is transparent to Pause frames.
VLAN The media converter is transparent to 802.1Q VLAN tagged packets.
Duplex Full and half duplex operation supported.
Jumbo Packets Transparent to jumbo packets up to 10KB.
Remote Loopback The media converter can perform a loopback on each 1000Base-X fiber interface.


Browse for more products in the same category as this item:

Perle > Perle Media Converters > Perle Stand-Alone Media Converters > Perle Unmanaged Media Converters > Perle Unmanaged Fiber to Fiber > Perle Unmanaged 1000SX Fiber to Fiber

Product price is not filled in. This product cannot be purchased.



BB-232CDT $95.80
08000449 $1,519.52
05070104 $2,919.54
UPort 404A $345.82
70001699 $1,066.62
05062260 $1,326.00
06004880 $1,045.20
05061350 $868.14