Home > Perle > Perle Media Converters > Perle MCR Series Modular Media Converters > Perle Unmanaged Fiber to Fiber Modules > 1000SX MultiMode to 1000FX/LX/BX/EX/ZX Single Mode Fiber Modules >

05061480

05061480
See any errors on this page?
Please let us know.
  
Perle C-1000MM-M2LC2 - Gigabit Ethernet Fiber to Fiber Media Converter Module. 1000BASESX  multimode (LC) to 1000BASELX 1310nm Extended multimode (LC)
MSRP: $1,049.00
ESP Price: $818.22
Contact us for Partner Pricing. (more info)


Free Shipping
Availability: Usually Ships in 24 Hours; However, Due To Shortages Contact Sales to Verify
Product Code: 05061480

Description Technical Specs Drivers & Downloads
 

Installed in a high density Perle Media Converter Chassis, Perle's feature rich C-1000MM Gigabit Fiber to Fiber Media Converter Modules enable transparent fiber extension of 1000Base-SX multimode fiber to 1000Base-SX multimode or 1000Base-LX/EX/ZX/BX single mode fiber.

Perle's advanced features make the end to end fiber link completely transparent. This allows for more efficient troubleshooting and less on-site maintenance. In addition, a lifetime warranty and free worldwide technical support make Perle's C-1000MM Gigabit Fiber to Fiber Media Converter Modules the smart choice for IT professionals.

Whether you need to extend multimode to multimode or multimode to single mode, Perle has an extensive range of C-1000MM Gigabit Fiber to Fiber Media Converter Modules to meet your fiber conversion requirement.
Features
  • 1000Base-SX to 1000Base-X Fiber to Fiber Media Converter
  • Multimode to multimode or multimode to single mode
  • Extend multimode fiber to 160km and beyond ( through cascading )
  • Choice in SC, LC and ST fiber connector models
  • Signal regeneration prevents signal degradation
  • Advanced Features: Smart Link Pass-Through, Fiber Fault Alert,
    loopback for each fiber connection
  • High density applications with Perle Media Converter Chassis

C-1000MM Fiber to Fiber Features: 1000Base-SX to 1000Base-X

Auto-Negotiation The 1000Base-X fiber interfaces negotiate according to 802.3 clause 37.
Smart Link Pass-Through When the Link Mode switch is placed into Smart Link Pass-Through mode, the 1000BASE TX port will reflect the state of the 1000Base-X media converter port. This feature can be used whether fiber auto-negotiation is enabled or disabled.
Fiber Fault Alert With Fiber Fault Alert the state of the 1000Base-X receiver is passed to the 1000Base-X transmitter. This provides fault notification to the partner device attached to the 1000Base-X interface of the media converter. If the 1000Base-X transmitter is off as a result of this fault it will be turned on periodically to allow the condition to clear should the partner device on the 1000Base-X be using a similar technique. This eliminates the possibility of lockouts that occur with some media converters. Applies only when fiber auto-negotiation is disabled.
Signal Regeneration Signal regeneration maintains signal integrity and allows for maximum fiber to fiber connections without degradation.
Cascading Media Converters can be cascaded. Two or more media converters can be chained in a link to achieve even greater distances.
Pause (IEEE 802.3x) Pause signaling is an IEEE feature that temporarily suspends data transmission between two devices in the event that one of the devices becomes overwhelmed. The media converter is transparent to Pause frames.
VLAN The Media Converter is transparent to 802.1Q VLAN tagged packets.
Duplex Full and half duplex operation supported.
Jumbo Packets Transparent to jumbo packets up to 10KB.
Remote Loopback The Media Converter can perform a loopback on each 1000Base-X fiber interface.


Browse for more products in the same category as this item:

Perle > Perle Media Converters > Perle MCR Series Modular Media Converters > Perle Unmanaged Fiber to Fiber Modules > 1000SX MultiMode to 1000FX/LX/BX/EX/ZX Single Mode Fiber Modules

Product price is not filled in. This product cannot be purchased.



05050484 $329.16
05059660 $404.82
08000004 $906.88