Perle 05061200 - Express Systems & Peripherals

Home > Perle > Perle Media Converters > Perle MCR Series Modular Media Converters > Perle Unmanaged Fiber to Fiber Modules > 1000SX MultiMode to 1000FX/LX/BX/EX/ZX Single Mode Fiber Modules >

05061200

See any errors on this page?
Please let us know.

Perle C-1000MM-M2LC05 - Gigabit Ethernet Fiber to Fiber Media Converter Module. 1000BASESX 850nm multimode (LC) [550 m/1804 ft.] to 1000BASESX 850nm multimode (LC) [550 m/1804 ft.]

MSRP: $708.00

ESP Price: $552.24

Contact us for Partner Pricing. (more info)

Availability: Usually Ships in 24 Hours; However, Due To Shortages Contact Sales to Verify
Product Code: 05061200

Description

Technical Specs

Drivers & Downloads

Installed in a high density Perle Media Converter Chassis, Perle's feature rich C-1000MM Gigabit Fiber to Fiber Media Converter Modules enable transparent fiber extension of 1000Base-SX multimode fiber to 1000Base-SX multimode or 1000Base-LX/EX/ZX/BX single mode fiber.

Perle's advanced features make the end to end fiber link completely transparent. This allows for more efficient troubleshooting and less on-site maintenance. In addition, a lifetime warranty and free worldwide technical support make Perle's C-1000MM Gigabit Fiber to Fiber Media Converter Modules the smart choice for IT professionals.

Whether you need to extend multimode to multimode or multimode to single mode, Perle has an extensive range of C-1000MM Gigabit Fiber to Fiber Media Converter Modules to meet your fiber conversion requirement.

Features

1000Base-SX to 1000Base-X Fiber to Fiber Media Converter
Multimode to multimode or multimode to single mode
Extend multimode fiber to 160km and beyond ( through cascading )
Choice in SC, LC and ST fiber connector models
Signal regeneration prevents signal degradation
Advanced Features: Smart Link Pass-Through, Fiber Fault Alert,
loopback for each fiber connection
High density applications with Perle Media Converter Chassis

C-1000MM Fiber to Fiber Features: 1000Base-SX to 1000Base-X

Auto-Negotiation	The 1000Base-X fiber interfaces negotiate according to 802.3 clause 37.
Smart Link Pass-Through	When the Link Mode switch is placed into Smart Link Pass-Through mode, the 1000BASE TX port will reflect the state of the 1000Base-X media converter port. This feature can be used whether fiber auto-negotiation is enabled or disabled.
Fiber Fault Alert	With Fiber Fault Alert the state of the 1000Base-X receiver is passed to the 1000Base-X transmitter. This provides fault notification to the partner device attached to the 1000Base-X interface of the media converter. If the 1000Base-X transmitter is off as a result of this fault it will be turned on periodically to allow the condition to clear should the partner device on the 1000Base-X be using a similar technique. This eliminates the possibility of lockouts that occur with some media converters. Applies only when fiber auto-negotiation is disabled.
Signal Regeneration	Signal regeneration maintains signal integrity and allows for maximum fiber to fiber connections without degradation.
Cascading	Media Converters can be cascaded. Two or more media converters can be chained in a link to achieve even greater distances.
Pause (IEEE 802.3x)	Pause signaling is an IEEE feature that temporarily suspends data transmission between two devices in the event that one of the devices becomes overwhelmed. The media converter is transparent to Pause frames.
VLAN	The Media Converter is transparent to 802.1Q VLAN tagged packets.
Duplex	Full and half duplex operation supported.
Jumbo Packets	Transparent to jumbo packets up to 10KB.
Remote Loopback	The Media Converter can perform a loopback on each 1000Base-X fiber interface.